蒸压建材生产过程中钢渣安定性处理与活性化利用

钢渣安定性处理过程常常造成胶凝活性的损失。为此，本文利用改性助剂消除钢渣水化过程中产生的氢氧化物并生成胶凝产物，在蒸压建材的生产过程中实现钢渣安定性处理和游离氧化物的活性化利用，并避免单独处置钢渣造成的活性物质损失。研究表明，8%秸秆灰和3%磷酸二氢铵作为复合助剂制备的尾矿-钢渣蒸压试块体积稳定，抗压强度达24.0MPa。通过对蒸压样品游离氧化物消解率、化学结合水量及热重、XRD分析，得出钢渣安定性处理与活性化利用机制：硅质材料与钢渣中f-CaO水化生成的Ca(OH)₂结合迅速生成对体系力学强度有益的水化硅酸钙，避免因大量Ca(OH)₂积累造成体积膨胀；磷酸盐中的NH₄⁺、H₂PO₄^-与f-MgO结合生成磷酸铵镁及其他低溶度积复盐类矿物，进而消除因f-MgO水化生成Mg(OH)₂造成体积膨胀的隐患。试样在180℃蒸压4h后，f-CaO及f-MgO消解率分别可达86.28%、89.73%。本文将为利用钢渣大比例取代水泥和石灰生产蒸压建筑材料提供理论基础，对于提高钢渣利用率、减少碳排放具有重要价值。     

Behaviour of 54.4SiO2-13.7Na2O-1.7K2O-5.0CaO-12.4MgO-0.6Y2O3-11.3Al2O3-0.9B2O3 HT-SOFC glass sealant under oxidising and reducing atmospheres

The behaviour of the promising glass sealant 54.4SiO₂-13.7Na₂O-1.7K₂O-5.0CaO-12.4MgO-0.6Y₂O₃-11.3Al₂O₃-0.9B₂O₃ for solid oxide fuel cells (SOFCs) under SOFC operating conditions was studied. First, the kinetics of the crystallisation processes at the operating temperature (850 °C) was discussed (maximum exposure time of 1000 h), and the effect of crystallisation on the coefficient of thermal expansion (CTE) of the sealant was studied. Furthermore, the degradation processes at the interface of the glass sealant and functional SOFC materials (Crofer 22 APU, YSZ, and NiO(Ni)-YSZ) during exposure to 850 °C in oxidising and reducing atmospheres for 500 h were studied. The tests demonstrated good performance of the sealant studied and possibility of its application in SOFCs.     

Fabrication and thermoelectric properties of SrTiO3–TiO2 composite ceramics

The paper presents the results of preparing biphase SrTiO₃–TiO₂ ceramics as a promising system for n-type thermoelectrics using the features of a two-dimensional electron gas. Ceramics was obtained by reactive spark plasma sintering of SrCO₃ and TiO₂. The dynamics of phase transformations are shown; it is clarified that phase transformations are not the driving force of sintering. The mutual stabilization of the SrTiO₃ and TiO₂ phases is shown. Unique data on the assessment of the temperature gradient in the system have been obtained. A comparison of the thermoelectric characteristics of biphasic ceramics and its constituent phases allows concluding that the role of the two-dimensional electron gas is reduced to modulating the properties of bulk phases. Clear signs of size quantization were detected by the X-ray luminescence method, which is expressed in the blueshift of the luminescence spectrum by 22.3 ± 0.8 meV.     

Determination of olaquindox,carbadox and cyadox in animal feeds by ultra-performance liquid chromatography tandem mass spectrometry

Olaquindox, carbadox, and cyadox are chemically synthesised antibacterial and growth-promoting agents for animals. At high doses they may exert mutagenicity and hepatic and adrenal toxicities in animals. Regrettably, these substances are frequently abused or misused when added into animal feeds. Thus, developing a sensitive and reliable method for simultaneous determination of olaquindox, carbadox, and cyadox in different kinds of animal feeds is crucially important for food safety monitoring. In this paper we optimised instrumental conditions, extraction solvents, solid phase extraction cartridges, and pH of the loading solvents on the Oasis HLB cartridge. Under the optimal conditions, mean recoveries ranged from 74.1 to 111%, and intra-day and inter-day variations were lower than 14.6% and 10.8%, respectively. The limits of quantification for olaquindox, carbadox, and cyadox were 0.05 mg kg^?1, 0.10 mg kg^?1, and 0.025 mg kg^?1, respectively. The proposed method uses ultra-performance liquid chromatography tandem mass spectrometry and is sensitive and reliable for the simultaneous determination of olaquindox, carbadox, and cyadox in three kinds of animal feeds (specifically, mixed feed, concentrated feed, and additive premixed feed). This method has good precision, high sensitivity, and good reproducibility, and thus it can be used for convenient and accurate determination of olaquindox, carbadox, and cyadox in different kinds of animal feeds.     

分析铁路改良粉细砂填料应用性能试验

在设计铁路路基的填料时,最常出现的是在进行铁路建设的地方就地取材。在以粉细砂为主的地区通常会选择用粉细砂作为铁路的填料,在所有的填料中,粉细砂填料属于C组类型填料,但是因为两个方面的原因需要对其进行一定的改良,一方面是因为粉细砂的粒径比较单一、级配不好,K30不能够满足规范标准的要求;另一方面则是因为大型机械不能够进行施工。本文通过掺入不同体积A、B组砾砂填料到粉细砂填料中进行试验,结果显示这种操作可以在不同程度上提高K30的值,从而在达到相关设计要求的同时解决施工方面的难题。     

Numerical modeling of wave propagation in anisotropic viscoelastic laminated materials in transient regime: Application to modeling ultrasonic testing of composite structures

Composite laminate structures remain an important family of materials used in cutting-edge industrial areas. Building efficient numerical modeling tools for high-frequency wave propagation in order to represent ultrasonic testing experiments of these materials remains a major challenge. In particular, incorporating attenuation phenomena within anisotropic plies, and thin intermediate isotropic layers between the plies often represent significant obstacles for standard numerical approaches. In our work, we address both issues by proposing a systematic study of the fully discrete propagators associated to the Kelvin-Voigt, Maxwell, and Zener models, and by incorporating effective transmission conditions between plies using the mortar element method. We illustrate the soundness of our approach by proposing intermediate one-dimensional and two-dimensional numerical evidence, and we apply it to a more realistic configuration of a curved laminate composite structure in a three-dimensional setting.     

低阶煤颗粒-气/油泡间的诱导时间研究

为表征低阶煤颗粒-气/油泡间矿化过程的差异,通过Sutherland理论下固体颗粒进入泡沫产品的总概率(E)和浮选速率常数(k)之间关系,并结合低阶煤颗粒-气/油泡的浮选速率试验,求得了低阶煤颗粒-气/油泡间的诱导时间。浮选实验研究表明,在相同的捕收剂消耗量下低阶煤-油泡浮选产率均高于低阶煤-气泡浮选产率。诱导时间测试表明,低阶煤颗粒-油泡间的诱导时间(35 ms)要明显低于低阶煤颗粒-气泡间的诱导时间(93 ms)。上述实验结果表明,油泡表面的疏水性要强于传统浮选气泡表面的疏水性。然而,进一步利用Sutherland理论中固体颗粒进入泡沫产品的总概率和浮选速率常数之间的数学关系,并结合低阶煤颗粒-气/油泡的浮选速率试验求得的低阶煤颗粒-气/油泡间的诱导时间分别为9.67和8.46 ms,其与诱导时间测试仪分别测量的诱导时间差异很大。这主要是由于在实际浮选过程中气/油泡的上升速度分别为23.26和22.68 cm/s,其远高于2015EZ型诱导时间仪测试过程中气/油泡碰撞速度(2.0 cm/s)。因此,诱导时间理论计算表明气泡-颗粒间的碰撞速度对颗粒-气泡间的诱导时间影响很大。上述研究结果表明油泡浮选效果优于传统浮选的内在原因在于低阶煤颗粒-油泡间的诱导时间小于低阶煤颗粒-气泡间的诱导时间。     

Tribological behavior studies of chemically bonded phosphate ceramic coatings reinforced with modified multi-walled carbon nanotubes (MWCNTs)

To improve the wear resistance of the chemically bonded phosphate ceramic coatings, MWCNTs are selected as the reinforcement after the modification. The high temperature wear experiment is carried out to investigate the wear behavior of the coatings with different temperatures. The results suggest that, when the temperature is below 500℃, MWCNTs can decrease friction coefficient, and the lowest friction coefficient is about 0.28, but MWCNTs lose the lubricant function at 500℃ and the friction coefficient keeps at the level of ~ 0.68. In addition, the wear resistance of coatings is improved with the introduction of MWCNTs at 100℃ and 300℃ (the wear rate is below 15X10^-3mm³/Nm), but keeps similar level at 500℃ (the wear rate is ~ 22 × 10⁻³mm³/Nm). Besides, the wear mechanism of the coatings reinforced by MWCNTs is also investigated based on the wear behavior and microstructural characterizations. MWCNTs improve the fracture toughness by preventing the crack generation and forming the bridge when crack occurs, which leads to smooth wear tracks and good wear resistance of coatings. The coatings with MWCNTs achieve poor wear resistance at 500℃ because MWCNTs lose their strength and resistance to fatigue by oxidizing.     

Interleukin-1β Modulation of the Mechanobiology of Primary Human Pulmonary Fibroblasts: Potential Implications in Lung Repair

Pro-inflammatory cytokines like interleukin-1β (IL-1β) are upregulated during early responses to tissue damage and are expected to transiently compromise the mechanical microenvironment. Fibroblasts are key regulators of tissue mechanics in the lungs and other organs. However, the effects of IL-1β on fibroblast mechanics and functions remain unclear. Here we treated human pulmonary fibroblasts from control donors with IL-1β and used Atomic Force Microscopy to unveil that IL-1β significantly reduces the stiffness of fibroblasts concomitantly with a downregulation of filamentous actin (F-actin) and alpha-smooth muscle (α-SMA). Likewise, COL1A1 mRNA was reduced, whereas that of collagenases MMP1 and MMP2 were upregulated, favoring a reduction of type-I collagen. These mechanobiology changes were functionally associated with reduced proliferation and enhanced migration upon IL-1β stimulation, which could facilitate lung repair by drawing fibroblasts to sites of tissue damage. Our observations reveal that IL-1β may reduce local tissue rigidity by acting both intracellularly and extracellularly through the downregulation of fibroblast contractility and type I collagen deposition, respectively. These IL-1β-dependent mechanical effects may enhance lung repair further by locally increasing pulmonary tissue compliance to preserve normal lung distension and function. Moreover, our results support that IL-1β provides innate anti-fibrotic protection that may be relevant during the early stages of lung repair.     

基于旋翼负压混合吸附的爬壁清洗机器人系统动力学性能研究

针对爬壁清洗机器人越障时,负压装置的吸附力下降导致吸附不稳定的问题,设计了一种旋翼负压混合吸附工作的多边形履带清洗机器人,并对爬行稳定性及越障性能进行了动力学分析。首先根据机器人爬壁的运动原理,建立机器人沿玻璃幕墙上的动力学模型,计算出电机理论驱动力矩;其次分析机器人在跨越障碍过程中的运动模型,结合与壁面接触的实际受力状态,对越障过程中关键阶段的本体倾翻、滑移两种失效形式进行运动学和动力学分析;然后根据玻璃幕墙实际的障碍高度,确定多边形履带的参数和理论驱动力矩的大小,并研制了实验样机进行爬行和越障试验,结果表明所设计的机器人具有良好的越障性能。